Welcome to the Revolution

Hi there, welcome to my blog - La Revolution Deux. It's an odd name - but I like it! Here you will find all the info on my various DIY Guitar effects builds, amplifiers and guitars. Everything from a humble Ibanez tubescreamer to the holiest KLON Overdrive.

You may also find a few effects builds that I am looking to move on - usually in exchange for other effects/gear/cash. You can always check my ebay account to see what I've got up for grabs.

Have fun, enjoy the blog - Fred Briggs :-)

CONTACT ME



Feel free to get in contact with me about anything you see on this blog or with any general questions about guitars, amplifiers and effects, I'll be happy to answer! Just click the button above to email me directly or alternately my email address is fredbriggs2007 [at] googlemail [dot] com

Search This Blog

Wednesday, 14 March 2012

Mictester - Silicon Tonebender


If you're into fuzz then here's a gem for you - a super consistent silicon fuzz monster. Here's the schematic and vero layout. For more info here's the freestompboxes.org forum topic (*complete with attached bitching over circuit credits and origin*): http://www.freestompboxes.org/viewtopic.php?f=13&t=7767


Here's mictester's advice on tweaking:

"Adjustment: set the 1k "Abuse" pot halfway. Play though it, and adjust 5k preset until "gating" just stops. That's it!

You'll find that it has plenty of output, that the "Abuse" control gives a good range of colour, the "Sparkle" control has a very wide range and the sound is remarkably reminiscent of early Jeff Beck (certainly not a bad thing!).

Possible mods:

Put small value capacitors from base to collector of the middle two transistors - start with 47pF. This "smooths out" the sound a lot, but reduces the treble available.

If you have radio interference, put 100pF from base of the first transistor to ground.

Experiment with the capacitor values in the tone control - the 8n2 could go as low as 3n3, which would give a ridiculous range of treble control!

Increase the value of the 47k feedback / bias resistor - try as high as 470k. The gain will rise, the touch sensitivity will disappear, and it will become a high gain screaming monster! "


Now - here's a similar design posted back in 2003 by Gus Smalley; the "Hot Silicon":


Take away the furore over circuit credits and what not and you've got a great sounding design here - it's an absolutely cracking fuzz circuit (I actually prefer it to messing about with Germanium transistors!). Give it a try - you won't be disapointed!
And here's an image of a completed build by LaceSensor:


4 comments:

  1. Hello, has anyone tried the vero board layout here? I have had trouble getting it to work. Any advice welcome.
    I have tried exchanging the 10k resistors on the collectors of the BC109Cs but to no avail. I did get a buzzy signal through at one point but not now. I also tried 10k trimmers in series with the 10k resistors on the collectors, but again no joy. One thing I did wonder is should there be a link between pin 1 and 2 on the VR to ground? Regardless of this I should get a signal I reckon. Anyway, might just draw my own vero layout like normal. That's what I get for taking shortcuts :P.
    Anyway, if anyone can verify the board layout is correct and works, this would be great.
    cheers - Brett

    ReplyDelete
  2. This comment has been removed by the author.

    ReplyDelete
  3. Probably a little late, but for anyone else who come across this, yes the board is correctand works. No, the trimmer does not need lugs connecting: The uppermost lug is not connected to anything, the other two lugs form a variable resistor that adjusts the bias of the third transistor by altering the emmitter resistance to ground: It allows you to dial in anything from smooth and sustaining to gated and splatty.

    ReplyDelete
  4. Простенько и со вкусом. Винтажный звук со всеми косяками винтажа.

    ReplyDelete

Comments are welcome on Revolution Deux. However, please do not spam links to unrelated sites - these comments will be removed! Thanks - Briggs.